Jlg 340AJ Service Manual User Manual Page 100
- Page / 348
- Table of contents
- TROUBLESHOOTING
- BOOKMARKS
Rated. / 5. Based on customer reviews
SECTION 3 - CHASSIS & TURNTABLE
3-60 – JLG Lift – 3121259
7. Remove bearing (15) and Nilos Ring (16) from pinion
(21) using external bearing puller or press.
8. Remove motor and motor adapter (22) and shims (28).
9. Remove ¾" bolts (7) from Worm Cap (20) using ¾"
socket. Remove shim (29) and seal (9) and discard.
10. Remove worm (32) from housing (25) by pushing worm
from motor end using steel rod and hammer. Bearing
cup (3) on hex end of worm will be forced out of hous-
ing. Once the bearing cup (2) has come out of housing
use soft hammer to tap worm on hex end to remove
other bearing cup (2) out the other end of housing.
11. Remove both bearings (2) from worm (32) from worm
using external bearing puller or press.
12. Bearing cup (17) can be removed from housing (25) by
lifting out (this is not a press fit just a close slip fit).
13. Bearing cup (15) can be removed from cap (18) using
small pry bar. Or by welding a small bead of weld on
internal diameter of cup, this is a press fit.
Assembly
1. Press bearing cup (15) into cap (18).
2. Place bearing cup (17) into housing (25).
3. Put face seal (23) on to hub of worm gear (31) with flap
of seal pointing away from gear.
4. Place worm gear (31) on press with face seal up and
press pinion (21) into worm gear. Place Nilos Ring (16)
on to pinion so that cup shape is up and press bearing
(15) on to pinion tight to Nilos Ring.
5. Turn assembly over and place spacer (24) on pinion
against gear hub so that large chamfer on I.D. of spacer
is against Bronze gear. Press Bearing (17) on to pinion
tight to spacer and gear.
6. Place pinion/gear assembly into housing. Place gear cap
(18) and shims (26) over gear/pinion assembly to
achieve a slight preload on pinion bearings. Remove cap
and shims and set shims aside. Install new cover plate
(19) on to cap using 6 screws (30) and shims (26) equal
to or close to equal to total thickness of shims just set
aside. Apply sealant (LocTite #515) to both sides of each
of these shims and tighten screws take care not to twist
these screws off. Clean extra sealant from surfaces of
cover plate. Apply a small amount of grease to this flap.
Set this assembly to the side.
7. Install bearing (2) on bore end of worm (32) only. This is
almost a slip fit, may have to be lightly tapped with soft
hammer.
8. Install worm (32) into housing (25), hex end first.
9. On bore end of worm, install bearing cup (2) into worm
bore of housing. Also on bore end of worm (32) install
motor adapter (22) and 1 shim (28 yellow) to housing
using ¾-13 x 1" bolts (6) and sealant. Torque to 75 ft-lbs.
(3.1 Nm) (these bolts will be replaced with motor bolts
when motor is mounted).
10. Install bearing cone (2) on hex end of worm (32). Place
bearing cup (2) over bearing and lightly tap cup into
bore using soft hammer.
11. Install worm cap (20) using proper shims (29) to achieve
0.000 to 0.001" (0.0000 to 0.0254 mm) end play. Apply
LocTite 242 to end of ¾-13 x 1.25" grade 5 bolts (7) and
LocTite #515 sealant to shims. Torque bolts to 75 ft-lbs.
(3.1 Nm).
12. Place pinion/gear assembly into housing so gear teeth
mesh with worm gear teeth. May have to turn worm or
gear set by hand to achieve this.
13. Apply LocTite #515 to surfaces of housing where cap
assembly will touch. This includes the vertical surfaces.
14. Place gear cap assembly and shims set aside in step 6,
over pinion assembly.
15. Apply LocTite 242 to end of eight 5/16" 12 point screws
(4) and torque to 20 ft-lbs. (0.84 Nm)
16. Install 4 small screws (30) through cover plate (18) and
into housing (25) tighten screws take care not the twist
these screws off.
17. Install seal (9) in worm cap at hex end of worm.
18. Install slew ring (14) using two 1/4" bolts (5) and washer
(1). Adjust backlash with pinion to 0.008/0.012" (0.203/
0.305 mm) and torque bolts to 10 ft-lbs. (0.42 Nm).
19. Fill unit with SHC 007 grease and grease pinion bearing
(15) thru fitting (11) with Mobil SHC 460 grease.
- P/N - 3121259 1
- AGENERAL 3
- BHYDRAULIC SYSTEM SAFETY 3
- CMAINTENANCE 3
- REVISON LOG 4
- TABLE OF CONTENTS 5
- SECTION 5 - HYDRAULICS 8
- 10
- LIST OF FIGURES 11
- SECTION 1. SPECIFICATIONS 17
- Major Component Weights 18
- Hydraulic Oil 18
- 1.6 FUNCTION SPEEDS 19
- Test Notes 19
- SECTION 1 - SPECIFICATIONS 20
- 1.7 OPERATOR MAINTENANCE 21
- SOCKET HEAD CAP SCREWS 26
- Magni Coating (Ref 4150701)* 30
- SECTION 2. GENERAL 31
- 2.2 SERVICE AND GUIDELINES 32
- Safety and Workmanship 32
- Cleanliness 32
- SECTION 2 - GENERAL 33
- Changing Hydraulic Oil 34
- Lubrication Specifications 34
- 2.4 CYLINDER DRIFT TEST 34
- Platform Drift 34
- 2-10 – JLG Lift – 3121259 40
- 3.1 TIRES AND WHEELS 41
- Tire Replacement 41
- Wheel and Tire Replacement 41
- Wheel Installation 41
- 3-2 – JLG Lift – 3121259 42
- 3.6 DRIVE MOTOR 43
- 3-4 – JLG Lift – 3121259 44
- 3121259 – JLG Lift – 3-5 45
- 3-6 – JLG Lift – 3121259 46
- 3121259 – JLG Lift – 3-7 47
- 3-8 – JLG Lift – 3121259 48
- 3121259 – JLG Lift – 3-9 49
- 3.7 DRIVE HUB 50
- Roll, Leak and Brake Testing 50
- Tightening and Torquing Bolts 50
- Measuring Rolling Torque 51
- Main Disassembly 51
- 3-12 – JLG Lift – 3121259 52
- Housing-Spindle Disassembly 53
- 3-14 – JLG Lift – 3121259 54
- 3121259 – JLG Lift – 3-15 55
- Cover Disassembly 56
- 3121259 – JLG Lift – 3-17 57
- Planet Gear Subassembly 58
- Spindle-Brake Subassembly 59
- 3-20 – JLG Lift – 3121259 60
- Housing-Spindle Subassembly 61
- Housing-Ring Gear Subassembly 62
- Cover Subassembly 63
- Main Assembly 64
- 3121259 – JLG Lift – 3-25 65
- 3-26 – JLG Lift – 3121259 66
- 3121259 – JLG Lift – 3-27 67
- 3-28 – JLG Lift – 3121259 68
- 3121259 – JLG Lift – 3-29 69
- 3.8 OSCILLATING AXLE SYSTEM 70
- 3121259 – JLG Lift – 3-31 71
- 3.10 SWING MOTOR 72
- 3121259 – JLG Lift – 3-33 73
- 3-34 – JLG Lift – 3121259 74
- Disassembly and Inspection 75
- 3-36 – JLG Lift – 3121259 76
- 3121259 – JLG Lift – 3-37 77
- 3-38 – JLG Lift – 3121259 78
- 3121259 – JLG Lift – 3-39 79
- 3-40 – JLG Lift – 3121259 80
- 3121259 – JLG Lift – 3-41 81
- 3121259 – JLG Lift – 3-43 83
- 3-44 – JLG Lift – 3121259 84
- 3121259 – JLG Lift – 3-45 85
- 3-46 – JLG Lift – 3121259 86
- 3121259 – JLG Lift – 3-47 87
- One Piece Stator Construction 88
- Two Piece Stator Construction 89
- Final Checks 90
- Installation 90
- 3.11 SWING DRIVE 90
- 3121259 – JLG Lift – 3-51 91
- 3-52 – JLG Lift – 3121259 92
- M20x2.5 Thread 93
- 3-54 – JLG Lift – 3121259 94
- Wear Tolerance 96
- Swing Bearing Torque Value 96
- 3121259 – JLG Lift – 3-59 99
- Assembly 100
- FROM LAST JIB 101
- (ORIENTATION LOOKING TOWARDS 102
- LOWER UPRIGHT) 102
- ROTATED 28.5° CW 102
- 3121259 – JLG Lift – 3-63 103
- 3-64 – JLG Lift – 3121259 104
- 3121259 – JLG Lift – 3-65 105
- (3) LIMIT SWITCHES ARE PART 105
- OF LOWER BOOM HARNESS 105
- SWITCH SW152 OF 105
- LOWER BOOM HARNESS 105
- 3-66 – JLG Lift – 3121259 106
- 3121259 – JLG Lift – 3-67 107
- SEE DETAIL 108
- 3121259 – JLG Lift – 3-69 109
- 3.13 ENGINE START CONDITIONS 110
- 3.14 ENGINE RPM LEVELS 110
- Engine Stop RPM 110
- Idle RPM 110
- Mid Engine RPM 110
- 3121259 – JLG Lift – 3-71 111
- 3-72 – JLG Lift – 3121259 112
- 3.17 KUBOTA ENGINE 113
- Engine Oil Pressure Switch 113
- Engine Speed Sensor 113
- Coolant Sensor 114
- Glow Plugs 114
- Engine Speed Actuators 115
- Engine Start 116
- Alternator Excitation 116
- Fuel Pump 116
- Shutdown 116
- 3121259 – JLG Lift – 3-77 117
- 3-78 – JLG Lift – 3121259 118
- 3121259 – JLG Lift – 3-79 119
- 3-80 – JLG Lift – 3121259 120
- 3121259 – JLG Lift – 3-81 121
- 3-82 – JLG Lift – 3121259 122
- 3121259 – JLG Lift – 3-83 123
- 3-84 – JLG Lift – 3121259 124
- 3121259 – JLG Lift – 3-85 125
- 3-86 – JLG Lift – 3121259 126
- LP MIXER PURGE POINT 127
- HOSE FROM CARBON CANISTER 127
- 3-88 – JLG Lift – 3121259 128
- 3121259 – JLG Lift – 3-89 129
- VOLTAGE REGULATOR 130
- CONTROL BOX 130
- GENERATOR 130
- ASSEMBLY 130
- 3.22 COUNTERWEIGHT 131
- 3-92 – JLG Lift – 3121259 132
- 4.3 BOOM MAINTENANCE 133
- Disassembly of the Main Boom 133
- 4-2 – JLG Lift – 3121259 134
- Inspection 135
- Assembly of the Main Boom 135
- 4-4 – JLG Lift – 3121259 136
- 3121259 – JLG Lift – 4-5 137
- 4-6 – JLG Lift – 3121259 138
- 3121259 – JLG Lift – 4-7 139
- 4-8 – JLG Lift – 3121259 140
- 3121259 – JLG Lift – 4-9 141
- 4.5 ROTARY ACTUATOR 142
- Theory of Operation 142
- Tools Required 143
- Disassembly 144
- 3121259 – JLG Lift – 4-13 145
- 4-14 – JLG Lift – 3121259 146
- 3121259 – JLG Lift – 4-15 147
- 4-16 – JLG Lift – 3121259 148
- 3121259 – JLG Lift – 4-19 151
- 4-20 – JLG Lift – 3121259 152
- 3121259 – JLG Lift – 4-21 153
- Greasing Thrust Washers 154
- Testing the Actuator 154
- 3121259 – JLG Lift – 4-23 155
- Installation and Bleeding 156
- Troubleshooting 157
- 4-26 – JLG Lift – 3121259 158
- SECTION 5. HYDRAULICS 159
- Dip Method 160
- Spray Method 160
- Brush-on Method 160
- 5.2 HYDRAULIC CYLINDERS 161
- General Information 161
- Standard of Maintenance 161
- Inspection After Assembly 161
- SECTION 5 - HYDRAULICS 162
- Disassembly Procedure 164
- JIG FOR 168
- DUST WIPER 168
- 3121259 – JLG Lift – 5-21 179
- 3121259 – JLG Lift – 5-23 181
- 5-24 – JLG Lift – 3121259 182
- 3121259 – JLG Lift – 5-25 183
- 3121259 – JLG Lift – 5-29 187
- 5-30 – JLG Lift – 3121259 188
- 5.3 DRIVE PUMP 192
- Description 192
- The System Circuit 193
- Charge Pressure Relief Valve 194
- Plug Size and Torque Chart 215
- Initial Startup Procedures 218
- Pump Adjustment 222
- Control Neutral Adjustment 226
- Mechanical Neutral Adjustment 227
- Removing the Pump 228
- Electric Control Module 228
- Control Solenoids 229
- Charge Check / HPRV 231
- 5.4 GEAR PUMP 232
- 5.6 OIL SAMPLING 243
- Procedure 243
- INSTRUCTIONS 245
- Introduction 245
- 6.2 ANALYZER MENU STRUCTURE 246
- Using the Analyzer 247
- Analyzer 248
- Machine Setup 250
- Level Vehicle Description 250
- 3121259 – JLG Lift – 6-7 251
- 6-8 – JLG Lift – 3121259 252
- PLATFORM MODULE 253
- GROUND MODULE 253
- 6-10 – JLG Lift – 3121259 254
- 3121259 – JLG Lift – 6-11 255
- 6-12 – JLG Lift – 3121259 256
- 3121259 – JLG Lift – 6-13 257
- 6-14 – JLG Lift – 3121259 258
- 3121259 – JLG Lift – 6-15 259
- Ground Control Switches 260
- Platform Control Switches 260
- 3121259 – JLG Lift – 6-17 261
- 6-18 – JLG Lift – 3121259 262
- 3121259 – JLG Lift – 6-19 263
- ANALYZER 264
- 3121259 – JLG Lift – 6-21 265
- 6-22 – JLG Lift – 3121259 266
- 3121259 – JLG Lift – 6-23 267
- 6-24 – JLG Lift – 3121259 268
- 3121259 – JLG Lift – 6-25 269
- 6-26 – JLG Lift – 3121259 270
- 3121259 – JLG Lift – 6-27 271
- 6-28 – JLG Lift – 3121259 272
- 3121259 – JLG Lift – 6-29 273
- 6-30 – JLG Lift – 3121259 274
- 3121259 – JLG Lift – 6-31 275
- 6-32 – JLG Lift – 3121259 276
- 6.6 SYSTEM FAULT MESSAGES 277
- 6-34 – JLG Lift – 3121259 278
- 3121259 – JLG Lift – 6-35 279
- 6-36 – JLG Lift – 3121259 280
- 3121259 – JLG Lift – 6-37 281
- 6-38 – JLG Lift – 3121259 282
- 3121259 – JLG Lift – 6-39 283
- 6-40 – JLG Lift – 3121259 284
- 3121259 – JLG Lift – 6-41 285
- 6-42 – JLG Lift – 3121259 286
- 3121259 – JLG Lift – 6-43 287
- 6-44 – JLG Lift – 3121259 288
- 3121259 – JLG Lift – 6-45 289
- 6-46 – JLG Lift – 3121259 290
- 3121259 – JLG Lift – 6-47 291
- 6-48 – JLG Lift – 3121259 292
- 3121259 – JLG Lift – 6-49 293
- 6-50 – JLG Lift – 3121259 294
- 3121259 – JLG Lift – 6-51 295
- 6-52 – JLG Lift – 3121259 296
- 3121259 – JLG Lift – 6-53 297
- 6-54 – JLG Lift – 3121259 298
- 3121259 – JLG Lift – 6-55 299
- 6-56 – JLG Lift – 3121259 300
- 3121259 – JLG Lift – 6-57 301
- 6-58 – JLG Lift – 3121259 302
- 3121259 – JLG Lift – 6-59 303
- 6-60 – JLG Lift – 3121259 304
- 3121259 – JLG Lift – 6-61 305
- 6-62 – JLG Lift – 3121259 306
- 3121259 – JLG Lift – 6-63 307
- 6-64 – JLG Lift – 3121259 308
- 3121259 – JLG Lift – 6-65 309
- 6-66 – JLG Lift – 3121259 310
- 3121259 – JLG Lift – 6-67 311
- 6-68 – JLG Lift – 3121259 312
- 3121259 – JLG Lift – 6-69 313
- 6-70 – JLG Lift – 3121259 314
- 3121259 – JLG Lift – 7-1 315
- Resistance Measurement 316
- Continuity Measurement 316
- Current Measurement 317
- TO ELECTRICAL CONNECTIONS 317
- AMP Seal 318
- AMP Mate-N-Lok 319
- DIN Connectors 319
- Exclusions 319
- 7-6 – JLG Lift – 3121259 320
- AMP JUNIOR TIMER 320
- SEALED ENCLOSURES 320
- 7.4 AMP CONNECTOR 321
- 7-8 – JLG Lift – 3121259 322
- Wedge Lock 323
- Service - Voltage Reading 323
- 7-10 – JLG Lift – 3121259 324
- 7.5 DEUTSCH CONNECTORS 325
- DT/DTP Series Assembly 325
- DT/DTP Series Disassembly 325
- HD30/HDP20 Series Assembly 326
- HD30/HDP20 Series Disassembly 326
- 3121259 – JLG Lift – 7-13 327
- 7-14 – JLG Lift – 3121259 328
- 00111963-G 329
- 7-16 – JLG Lift – 3121259 330
- 1001119638-G 331
- 7-18 – JLG Lift – 3121259 332
- 7-20 – JLG Lift – 3121259 334
- KUBOTA ENGINE HARNESS 336
- GENERATOR HARNESS 337
- GM ENGINE HARNESS 338
- 7-26 – JLG Lift – 3121259 340
- 3121259 – JLG Lift – 7-29 343
- 7-30 – JLG Lift – 3121259 344
- 1001120020-C 345
- 7-32 – JLG Lift – 3121259 346
- JLG Worldwide Locations 348
Related products and manuals for Special machinery Jlg 340AJ Service Manual
(138 pages)
(178 pages)
Special machinery Jlg LSS Boom User Manual
(68 pages)
(68 pages)
(108 pages)
(88 pages)
(169 pages)© 2020, manymanuals.com. All rights reserved. | 0.286 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comments to this Manuals