Jlg 601S Service Manual User Manual Page 75
- Page / 240
- Table of contents
- TROUBLESHOOTING
- BOOKMARKS
Rated. / 5. Based on customer reviews
SECTION 3 - CHASSIS & TURNTABLE
3120866 – JLG Lift – 3-35
BALL GUIDE AND SLIPPER RETAINER
Inspect the ball guide and slipper retainer for damage,
discoloration, or excessive wear. A discolored ball guide
or slipper retainer indicates excessive heat. Do not reuse.
VALVE PLATE
The condition of the valve plate is critical to the efficiency
of the motor. Inspect the valve plate surfaces carefully for
excessive wear, grooves, or scratches. Replace or resur-
face grooved or scratched valve plates. Measure the valve
plate thickness and replace if worn beyond the minimum
specification. Valve plates may be resurfaced to the speci-
fications shown in the drawing, provided resurfacing will
not reduce the thickness below the minimum specifica-
tion.
SWASHPLATE AND JOURNAL BEARINGS
Inspect the running face, servo ball-joint, and swashplate
journal surfaces for damage or excessive wear. Some
material transfer may appear on these surfaces and is
acceptable providing the surface condition meets specifi
-
cations shown. Measure the swashplate thickness from
the journals to the running face. Replace swashplate if
damaged or worn beyond minimum specification.
Replace swashplate if the difference in thickness from one
side to the other exceeds specification.
Inspect the journal bearings for damage or excessive
wear. Replace journal bearings if scratched, warped, or
excessively worn. The polymer wear layer must be
smooth and intact.
SHAFT BEARINGS
Inspect bearings for excessive wear or contamination.
Rotate the bearings while feeling for uneven movement.
Bearings should spin smoothly and freely. Replace bear
-
ings that appear worn or do not rotate smoothly.
SHAFT
Inspect the motor shaft. Look for damage or excessive
wear on the output and block splines. Inspect the bearing
surfaces and sealing surface. Replace shafts with dam
-
aged or excessively worn splines, bearing surfaces, or
sealing surfaces.
Slipper retainer
Ball guide
3.83 mm [0.151 in] min.
0.025 mm
[0.001 in]
0.0076 mm
[0.00030 in]
convex max
LV
25.8 mm
[1.015 in]
24.6 mm
[0.969 in]
KV
Thickness equality
side to side:
0.05 mm [0.002 in]
0.0025 mm
[0.0001 in]
- P/N - 3120866 1
- ADE System Identification 3
- – JLG Lift – 4
- PRECAUTIONS 5
- REVISON LOG 6
- (Continued) 10
- TABLE OF CONTENTS 11
- SECTION 1. SPECIFICATIONS 17
- 1-2 – JLG Lift – 3120866 18
- SECTION 1 - SPECIFICATIONS 19
- Te st N o tes 19
- 1.5 TORQUE REQUIREMENTS 19
- 1.6 LUBRICATION 20
- Ford LRG425 Engine 20
- Deutz F3M1011F Engine 20
- Hydraulic Oil 21
- Lubrication Specifications 21
- 1.7 PRESSURE SETTINGS 21
- 1.8 CYLINDER SPECIFICATIONS 22
- 1.9 MAJOR COMPONENT WEIGHTS 22
- 1.11 SERIAL NUMBER LOCATIONS 23
- SECTION 2. GENERAL 27
- 2-2 – JLG Lift – 3120866 28
- 3120866 – JLG Lift – 2-3 29
- 2-4 – JLG Lift – 3120866 30
- 3120866 – JLG Lift – 2-5 31
- 2-6 – JLG Lift – 3120866 32
- SECTION 2 - GENERAL 33
- 2.8 AMP CONNECTOR 33
- AMP Connectors 33
- Wedge Lock 35
- Service - Voltage Reading 35
- 3.1 TORQUE HUB, DRIVE 41
- 3-2 – JLG Lift – 3120866 42
- 3120866 – JLG Lift – 3-3 43
- 3120866 – JLG Lift – 3-5 45
- 3-6 – JLG Lift – 3120866 46
- 3120866 – JLG Lift – 3-7 47
- 3-8 – JLG Lift – 3120866 48
- 3120866 – JLG Lift – 3-9 49
- 3120866 – JLG Lift – 3-11 51
- 3.3 DRIVE BRAKE - AUSCO 52
- 3120866 – JLG Lift – 3-13 53
- 3.4 DRIVE BRAKE - MICO 54
- 3120866 – JLG Lift – 3-15 55
- Bleeding 56
- Spare Parts Kits 57
- 3-18 – JLG Lift – 3120866 58
- Disassembly and Assembly 59
- 3-20 – JLG Lift – 3120866 60
- 3120866 – JLG Lift – 3-21 61
- 3-22 – JLG Lift – 3120866 62
- Assembly Notes 63
- 3-24 – JLG Lift – 3120866 64
- Te st i n g a n d Se t u p 65
- 3.6 DRIVE MOTOR ADJUSTMENT 66
- Description 67
- Shaft Seal Replacement 67
- Loop Flushing Valve 68
- 3120866 – JLG Lift – 3-31 71
- 3-32 – JLG Lift – 3120866 72
- 3120866 – JLG Lift – 3-33 73
- Slipper retainer 75
- Ball guide 75
- 3120866 – JLG Lift – 3-37 77
- 3-38 – JLG Lift – 3120866 78
- 3120866 – JLG Lift – 3-39 79
- 3-40 – JLG Lift – 3120866 80
- Initial Start-up Procedures 81
- 3-42 – JLG Lift – 3120866 82
- PROCEDURE AND LOCKOUT TEST 83
- Lockout Cylinder Bleeding 83
- Oscillating Axle Lockout Test 83
- 3.10 STEER ADJUSTMENTS 84
- 3120866 – JLG Lift – 3-45 85
- .0015" Feeler Gauge 86
- 3120866 – JLG Lift – 3-47 87
- 3-48 – JLG Lift – 3120866 88
- Swing Bearing Torque Values 89
- 3.13 SWING BRAKE - AUSCO 89
- 3120866 – JLG Lift – 3-51 91
- 3.14 SWING MOTOR 92
- Reassembly 93
- Motor Timing 94
- 3120866 – JLG Lift – 3-55 95
- 3-56 – JLG Lift – 3120866 96
- 3120866 – JLG Lift – 3-57 97
- 3-58 – JLG Lift – 3120866 98
- Mounting-Controller 99
- 3-60 – JLG Lift – 3120866 100
- 3120866 – JLG Lift – 3-61 101
- Troubleshooting 102
- 3120866 – JLG Lift – 3-63 103
- 3.19 THROTTLE CHECKS AND 104
- ADJUSTMENTS - DEUTZ ENGINE 104
- (PRIOR TO S/N 61306) 104
- 3120866 – JLG Lift – 3-65 105
- Failure Modes 106
- 3120866 – JLG Lift – 3-67 107
- Checking the Ignition 108
- 3.22 CHECKING THE FUEL 109
- S/N 58209) 110
- Performing Diagnostics 110
- Engine Module and Sensors 111
- 3-72 – JLG Lift – 3120866 112
- 3120866 – JLG Lift – 3-73 113
- 3-74 – JLG Lift – 3120866 114
- 3120866 – JLG Lift – 3-75 115
- 3-76 – JLG Lift – 3120866 116
- 3120866 – JLG Lift – 3-77 117
- 3-78 – JLG Lift – 3120866 118
- 3120866 – JLG Lift – 3-79 119
- 3120866 – JLG Lift – 3-81 121
- 3120866 – JLG Lift – 3-83 123
- ENGINE MODULE INPUTS/OUTPUTS 123
- THROTTLE POSITION (TP) SENSOR 123
- USE OF CIRCUIT TESTING TOOLS 123
- 3-84 – JLG Lift – 3120866 124
- Fuel System 125
- 3-86 – JLG Lift – 3120866 126
- FUEL METERING SYSTEM PURPOSE 126
- 3-88 – JLG Lift – 3120866 128
- 3120866 – JLG Lift – 3-89 129
- ELECTRONIC IGNITION 129
- IGNITION COIL 129
- ENGINE MODULE (ECM OR EPM) 129
- 3-90 – JLG Lift – 3120866 130
- 4.1 BOOM MAINTENANCE 131
- Disassembly Boom Sections 132
- 3120866 – JLG Lift – 4-3 133
- 4-4 – JLG Lift – 3120866 134
- 3120866 – JLG Lift – 4-5 135
- 4-6 – JLG Lift – 3120866 136
- Inspection 137
- Assembly 138
- 3120866 – JLG Lift – 4-9 139
- Installation 140
- Torque Procedures 140
- 4.3 WEAR PADS 141
- Main Boom 141
- 4-12 – JLG Lift – 3120866 142
- ADJUSTMENT 143
- 4.6 ROTATOR - HELAC 144
- Disassembly 144
- 4-16 – JLG Lift – 3120866 146
- 3120866 – JLG Lift – 4-17 147
- Lift, Swing, and Drive Cards 148
- Flow Control Card 148
- 4.8 FOOT SWITCH ADJUSTMENT 149
- 4-20 – JLG Lift – 3120866 150
- SECTION 5. HYDRAULICS 151
- SECTION 5 - HYDRAULICS 152
- 5.4 CYLINDER REPAIR 152
- Cleaning and Inspection 154
- 5.5 CYLINDER REMOVAL AND 158
- INSTALLATION 158
- Boom Lift Cylinder Removal 159
- Inspections and Adjustments 163
- Minor Repair and Replacement 166
- Platform Level 170
- 4 Wheel Steer (If Equipped) 170
- 5-24 – JLG Lift – 3120866 174
- 6.1 INTRODUCTION 177
- 6-2 – JLG Lift – 3120866 178
- SYSTEM ANALYZER 179
- 6.3 USING THE ANALYZER 179
- 6-4 – JLG Lift – 3120866 180
- HAND HELD ANALYZER 181
- 6-6 – JLG Lift – 3120866 182
- 6.6 MACHINE SETUP 184
- 6.7 LEVEL VEHICLE DESCRIPTION 184
- 3120866 – JLG Lift – 6-9 185
- 6-10 – JLG Lift – 3120866 186
- 3120866 – JLG Lift – 6-11 187
- 6-12 – JLG Lift – 3120866 188
- 4150365 - 3 189
- 6-14 – JLG Lift – 3120866 190
- 3120866 – JLG Lift – 6-15 191
- 6-16 – JLG Lift – 3120866 192
- 3120866 – JLG Lift – 6-17 193
- 6-18 – JLG Lift – 3120866 194
- 3120866 – JLG Lift – 6-19 195
- 6-20 – JLG Lift – 3120866 196
- 3120866 – JLG Lift – 6-21 197
- 6-22 – JLG Lift – 3120866 198
- 3120866 – JLG Lift – 6-23 199
- 6-24 – JLG Lift – 3120866 200
- 3120866 – JLG Lift – 6-25 201
- 6-26 – JLG Lift – 3120866 202
- 3120866 – JLG Lift – 6-27 203
- 6-28 – JLG Lift – 3120866 204
- 3120866 – JLG Lift – 6-29 205
- 4150364 - 6 206
- 3120866 – JLG Lift – 6-31 207
- 6-32 – JLG Lift – 3120866 208
- 3120866 – JLG Lift – 6-33 209
- 6-34 – JLG Lift – 3120866 210
- 3120866 – JLG Lift – 6-35 211
- 6-36 – JLG Lift – 3120866 212
- STRUCTURE 213
- 6-38 – JLG Lift – 3120866 214
- 3120866 – JLG Lift – 6-39 215
- 6-40 – JLG Lift – 3120866 216
- 3120866 – JLG Lift – 6-41 217
- 6-42 – JLG Lift – 3120866 218
- SECTION 7. SCHEMATICS 219
- SECTION 7 - SCHEMATICS 220
- JLG Worldwide Locations 240
Related products and manuals for Special machinery Jlg 601S Service Manual
(110 pages)
(114 pages)
(406 pages)
(84 pages)
(124 pages)
(98 pages)© 2020, manymanuals.com. All rights reserved. | 0.569 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comments to this Manuals